logo

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality

Basic Information
Place of Origin : Guangdong , China
Brand Name : PDKJ
Certification : CE ISO SGS
Model Number : Custom
Trade Information
Minimum Order Quantity : 1 unit
Price : 20000-45000 USD
Standard Packaging : Plywood Case
Delivery Time : 15-30 work days
Supply Ability : 100 set per month
Product Summary

Automatic spot welder for iron drums: locating datum and adjustable clamping hold 0.8 mm coaxiality, modular tooling for wide disc, narrow disc and cylinder, clamp-press-weld-hold-cool, per-weld monitoring.

Product Description
Contents

A Drum Runs True Or It Wobbles: Welding The Spots Is Easy, Holding 0.8 mm Coaxiality Is The Machine

Application story  ·  Automatic spot welding of iron drums - wide disc, narrow disc and plain cylinder - locating datum plus adjustable clamping, modular tooling for fast changeover

An iron drum is two flanged discs and a tube between them, and then it spins. So the question on the drawing is not whether the spots will weld - a spot welder will weld anything you put under it - it is whether the two discs end up on the same axis. Every spot shrinks as it cools and pulls the joint with it, and on a drum a few tenths of a millimetre off axis shows up as run-out at the rim, noise on the shaft and a bearing that dies early. That is why this machine is built around its fixture and not around its transformer.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Automatic spot welding machine for iron drums: vertical C-frame, large copper secondary, adjustable lower fixture with handwheel, swing-arm control panel, two hand starts

The Part: Two Discs, A Tube, And A Gap That Has To Close

The drum in these photographs is a drawn disc at each end and a short tube between them. The joints are the circle where each disc meets the tube wall, and each circle takes a ring of spots. Get the ring right and the joint is strong and even; get it wrong and one side pulls harder than the other, and the drum goes out of square before it ever reaches the balancing station.

The second complication is that the wall is thin. A drum is sheet metal, not bar stock - so the welding current and the press force have to be right for a thin wall, and the clamp has to hold the disc flat while the spots are made rather than letting it dish between them.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

The welded drum: two flanged discs and a tube between them, spot welded round the joint at each end

Locating Datum First, Welding Second

Both ends of this machine are tooling. The lower fixture carries a locating datum - a pin and a cylindrical guide that put the drum on the machine axis - and the upper tooling comes down on the same axis, so the part is held between two references instead of being dropped onto one. A fine adjustment lets the lower fixture be trimmed into line during setup, which is how the last half millimetre is taken out.

That arrangement is what produces the number on the drawing: after welding, coaxiality holds within plus or minus 0.8 mm, and it holds there from the first drum of the shift to the last one, because the part is not located by how carefully the operator set it down. Repeatability comes from the datum, not from the welder's eye.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Side view of a welded drum: the spots run round the joint where the tube meets each disc - the two discs have to stay on one axis

Modular Tooling: Wide Disc, Narrow Disc, Plain Cylinder

A drum family is not one part. The same machine has to run wide discs, narrow discs and plain cylinders, and on a fixed fixture each of those is a rebuild. Here the tooling is modular: the upper and lower electrodes, the stop blocks and the clamp modules are separate pieces that are changed or trimmed rather than remade, so the changeover is a set of swaps and a program, not a day of fitting.

The point that matters is that repeatability survives the change. A modular fixture is only worth having if the first part after a changeover sits where the last part of the previous batch sat - otherwise the changeover has just moved the problem to the setup sheet.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Drums from the same family, different disc width and different tube length - the change between them is tooling modules and a program

The Sequence Is Where The Strength Comes From

The weld cycle is not press-and-fire. It runs clamp, pre-press, weld, hold, cool - five stages, each with its own time and its own force. Clamping settles the parts against each other before any current flows; pre-press builds the force to full value so the interface is closed when the current arrives; the weld stage puts the current in; hold keeps the force on while the nugget solidifies; and the cool stage lets the joint come down before the electrode lifts.

That order is what a strong spot actually depends on. Fire into a joint that has not been closed and the current finds the loose contact and expels; release the force before the nugget has set and the joint tears as it shrinks. Running the five stages in the right order is how the welds come out at or above the specified strength, with no cold joints and no pull-outs.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

At the throat: the upper electrode assembly, the heavy copper secondary behind it, water lines in red and blue, and the fixture below

Two Hands, One Panel, No Reach

The control panel sits on a swing arm at operator height, so the person running the machine can see the screen, the fixture and the electrode at once instead of turning away to read a cabinet. Cycle start is two pushbuttons set either side of the fixture, which means both hands are occupied and clear of the electrode when the head comes down, and an emergency stop is within reach without moving.

It sounds like detail. On a machine that makes a few hundred drums a shift it is the difference between an operator who keeps a rhythm and one who works around the equipment.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Front of the machine: two green start buttons either side of the fixture and the swing-arm panel to the right

The Machine Records What It Did

Current, time and pressure are measured on every weld and shown on screen as the cycle runs, and the values are stored rather than displayed and forgotten. Thresholds are set for each of them, and outside those thresholds the machine alarms and captures the data around the event - so a run of weak welds is a record to look at, not an argument about what happened.

For a part that ends up in a rotating assembly, that record is worth more than the reject rate. It is how a process gets changed on purpose instead of by guesswork, and how a first-pass yield stops drifting back down after a few months of production.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Complete machine with the swing-arm panel: welding parameters displayed and stored per cycle, thresholds with alarm capture

Built On A Welding Frame, Not Around One

The frame is a welded steel C-frame on a common base with levelling pads, carrying the cylinder at the top, the secondary in the throat and the fixture at working height. The lower fixture height is set with a handwheel and screw, which is the adjustment that gets used most often - not to change the weld, but to put the joint at the same height for a different drum.

Because the base is a single machined plate, the machine can be set down on a normal floor without a pit or a foundation, and it can be moved as one piece when the line is rearranged.

Automatic Spot Welding Machine for Iron Drums with 0.8 mm Coaxiality 

Side view: C-frame on a common base, cylinder at the top, secondary in the throat, handwheel height adjustment at the bottom

Key Specifications

Item

Specification

Typical part

Iron drum - two flanged discs with a tube between them; also wide disc, narrow disc and plain cylinder

Joint

Resistance spot welding, a ring of spots round the joint at each end of the drum

Coaxiality after welding

Within +/- 0.8 mm, held repeatably from part to part

Locating

Dedicated locating datum on the lower fixture - locating pin and cylindrical guide put the drum on the machine axis

Upper tooling

Upper electrode on the same axis as the lower datum; part held between two references

Adjustment

Fine adjustment on the lower fixture for setting the axis during setup

Clamping

Adjustable clamping mechanism, set for the drum being run

Tooling system

Modular - upper and lower electrodes, stop blocks and clamp modules changed or trimmed for each variant

Changeover

Tooling modules plus program; wide disc / narrow disc / cylinder without rebuilding the fixture

Weld sequence

Clamp - pre-press - weld - hold - cool, with individual time and force per stage

Press

Pneumatic cylinder at the top of the frame, force adjustable; air preparation with filter regulator

Electrodes

Copper upper electrode and lower electrode, water-cooled

Secondary

Heavy copper secondary loop built into the frame throat, water-cooled

Control

Swing-arm panel at operator height - touch screen, parameters per drum variant

Start / safety

Two-hand start, one pushbutton either side of the fixture; emergency stop within reach

Monitoring

Current, time and pressure measured per weld, displayed and stored; threshold alarm with data capture

Height adjustment

Lower fixture set by handwheel and screw

Frame

Welded steel C-frame on a common base plate with levelling pads

Delivery

Built to the drum drawing and sample; coaxiality proved on customer parts before shipment

Where It Welds

•   Iron drums and spools where two discs are welded to a central tube and the assembly rotates

•   Drum, reel and bobbin bodies that have to run true after welding

•   Thin-wall cylindrical parts with a flange spot welded at one or both ends

•   Families of wide disc, narrow disc and plain cylinder parts built on one platform

•   Any rotating assembly where coaxiality is called out on the drawing and cannot be straightened afterwards

Tooling, electrodes and programs are built from the customer's drum drawing and a sample. We weld the first parts on the real drum, check coaxiality, and set force, current and the five-stage sequence before the machine ships.

How A Custom Machine Is Built

01   Drum drawing, joint position and coaxiality requirement review

02   Weld trial on sample drums - nugget, set-down, and coaxiality measured after welding

03   Process proposal - tooling concept, electrode arrangement, sequence, cycle estimate

04   Fixture, locating datum, clamp modules and electrode design in 3D

05   Frame, secondary, pneumatic and water circuit build

06   Control integration, parameter monitoring and threshold setup

07   Assembly and run-off on customer drums before shipment

08   Delivery, installation and commissioning on site

09   Operator training in changeover, then after-sales service and spare electrodes

Talk to Pudian Technology

Guangdong Pudian Automation Technology Co., Ltd builds resistance and laser welding equipment in-house - transformers, controllers, electrodes, fixtures and complete machines - one team, one solution. Send us the drum drawing, the joint position and the coaxiality you have to hold, and we will weld sample parts and send them back with a parameter sheet.

Guangdong Pudian Automation Technology Co., Ltd

WhatsApp / Tel: +13613793248    Email: jay@gd-pw.com

Website: https://www.spotlaserwelding.com/

Address: 1-2F, Building 3, Qichen Industrial Park, No. 26 Luxi 1st Road, Liaobu Town, Dongguan City, Guangdong Province, China


Send Us An Inquiry
We will reply to you within 24 hours.
Inquiry Details
Contact Information