The Water Is Part Of The Machine: Cooling On A Resistance Welder
2026/11/16
The Water Is Part of the Machine: Cooling on a Resistance Welder
A resistance welding machine is a device for pushing several thousand amps through copper without melting the copper. The weld itself lasts a fifth of a second; the machine has to do it forty times a minute for years. Water is what makes that possible, and it is the utility most often specified last, connected first, and checked never.
This is what the water is actually cooling, what the numbers mean, and what happens to a machine that is run on a hose and a hope.

A 1000 kVA seam welder with its two copper electrode wheels. Both wheels, both holders and the transformer behind them are water-cooled, which is why the hoses are as much a part of the machine as the copper is.
What the Water Cools
The weld heat is generated at the interface, between the sheets, but the current has to travel through the secondary circuit to get there. That circuit is copper, and copper at these currents heats up fast: the transformer secondary, the arms or shunts that carry current from the transformer to the holders, the holders themselves, and the electrode tips or wheels. All of it is water-cooled, and all of it is in series with the weld.
The electrodes are the hottest part, because they are closest to the heat and because they are the smallest cross-section in the path. A water-cooled tip runs its coolant through an internal passage a few millimetres from the contact face; if that passage scales up or the flow drops, the tip temperature climbs, the copper softens, and the tip starts to mushroom under force.
On larger machines the thyristors and the transformer windings also need cooling, and on inverter machines the power stack has its own circuit. That is why a 1000 kVA seam welder has more hose connections than a small press: there are more things in it that will fail without water.
Three Numbers, Not One
Flow is the number everybody checks, and it is the least informative on its own. Fifteen litres a minute at 15 degrees is a very different machine from fifteen litres a minute at 35 degrees, because the cooling capacity depends on the difference between the water and the part, not on the volume alone. In a workshop without a chiller, the inlet temperature in August can be 20 degrees above the January figure, and the same machine will start to feel its duty cycle for reasons that have nothing to do with the welding.
The third number is water quality, and it is the one nobody records. Hard water deposits scale in exactly the passages that matter — the electrode seat, the shunt bore, the transformer coil — and scale is an insulator. A circuit that still flows fifteen litres a minute can be transferring a fraction of the heat, because the metal is no longer touching the water. Conductivity matters in the other direction: very pure water is a poor conductor and some inverter circuits monitor it, while water that has been sitting in an open tank for a year grows things that block a 6 mm hose.

The secondary side of a press welder: copper shunts, brass holders, and the yellow and blue hoses that carry water into the same places the current goes.
What Fails When the Water Is Marginal
The sequence is always the same and always misdiagnosed. The tips run hot, soften and mushroom; the contact area grows; current density falls; the nuggets get smaller while the controller shows exactly the current it was told to deliver. An operator notices weak welds and turns the current up. The nuggets come back, the tips now overheat faster, and the expulsion starts. By the time anybody looks at the water, the machine has a reputation for being difficult on that job.
On the transformer the failure is slower and more expensive. Winding temperature rises, the thermal protection derates the machine, and a welder that was specified at 50 percent duty cycle starts to trip on a hot afternoon. The customer concludes the machine is under-specified. Sometimes it is. More often the chiller is undersized or the filter has not been cleaned since installation.
Closed Loop or Mains Water
Once-through cooling from the mains is cheap to install and expensive to live with: the water goes down the drain carrying the heat, the inlet temperature follows the season, and in many places the discharge is regulated. A closed loop with a chiller costs more up front and gives a stable inlet temperature, which is the single biggest improvement available to a shop welding coated or thick material.
Between the two sits the tank-and-pump arrangement that most small shops actually build: a few hundred litres, a pump, and no heat exchanger. It works in winter. In summer the tank reaches equilibrium at whatever the shop is, and the machine quietly loses a third of its duty cycle.
An Hour of Testing Beats a Spec Sheet
Cooling adequacy can be settled in an hour, with scrap parts and no instruments beyond a thermometer. Fit a new pair of tips, run two hundred welds at the production rate into scrap, and then look at the tip faces. A tip that has turned blue or straw-coloured is running too hot, and the number of welds it took to get there is the useful figure. Then put the thermometer in the return line: a rise of more than about ten degrees between inlet and return means the circuit is carrying away less heat than the machine is making.
Both tests are crude and both are repeatable, which is what matters. A shop that runs them once a quarter will notice a blocked filter or a warming tank long before the welds start coming out small.
What We Ask Before a Machine Ships
We ask four questions, and the answers change what we fit. What is the water source: mains, tank or chiller? What is the inlet temperature in the hottest month? What is the hardness, because a softener costs less than a transformer? And who will check the flow, how often, and where is it written down?
Component |
What it needs |
What fails without it |
Electrode tips or wheels |
Flow through the internal passage, clean water |
Mushrooming, then expulsion and marking |
Holders and shanks |
Steady flow, no scale |
Overheating, seizure, burnt seats |
Shunts and arms |
Flow at the joints, no air pockets |
Hot spots, then fatigue failure |
Transformer |
Flow and inlet temperature within rating |
Derating, then thermal trips |
Power stack |
Clean, low-conductivity water |
Thyristor failure, expensive and sudden |
- Check flow at the return, not at the pump, and write the figure on the machine.
- Record the inlet temperature monthly; a rising trend is a blocked filter or a full tank.
- Change the filter, not just clean it, and keep a spare on the shelf.
- Flush a machine that has been idle for months before it welds production.
A welding machine is specified by its kVA, its throat and its controller, and it survives on its water. The three are not equally interesting to talk about, which is exactly why the third one gets ignored until it costs a transformer.
PDKJ continues to provide customized laser welding and resistance welding solutions based on different materials, workpiece structures, welding requirements, and production applications.
Related Products

Part of the assembly floor in Dongguan, where the water circuit is tested before a machine is allowed to weld anything.
Contact PDKJ
Send us your part drawing or a sample, and our engineers will run a welding feasibility trial on your own material and recommend the equipment configured for your application.
WhatsApp: +86 136 1279 3248
Email: jay@gd-pw.com
Website: https://www.spotlaserwelding.com/contactus.html
Address: 1-2F, Building 3, Qichen Industrial Park, No. 26 Luxi 1st Road, Liaobu Town, Dongguan City, Guangdong Province, China