Twin-Head Spot Welding Machine with Fixed Centre Distance
Twin-head spot welding machine: two C-frame heads on one cast frame, independent cylinders, six cooling circuits, both spots welded from a single loading so the spacing is a machined dimension.
Two Spots On One Part: Weld Them One At A Time And The Spacing Is Whatever The Second Set-Up Gave You
Application story · Twin-head spot welding machine - two C-frame heads on one cast frame, independent cylinders and pressure, six cooling circuits, both spots welded from a single loading
A part with two welds is two set-ups. Load it, weld the first spot, take it out, put it back the other way round, weld the second - and now the distance between the two spots is not the drawing dimension any more. It is the drawing dimension plus whatever the fixture gave you twice, plus whatever the part did when the first nugget cooled and pulled. On a bracket that has to bolt up to something else, that distance is a functional dimension, and it is being set by handling.
Twin-head spot welding machine: two C-frame heads on one cast base, each with its own air cylinder, electrode arms, cooling and pressure - control cabinet and main electrical box on the right
One Part, Two Welds, One Distance That Has To Hold
The parts this machine is built for carry their two welds as a pair: a beam with a bracket at each end, a frame with two mounting ears, a panel with a stiffener on both sides. The pair is not two independent welds that happen to be on the same part - it is one pattern, and the pattern is what the next operation locates from.
Doing it in two set-ups works. It just puts the pattern tolerance into the hands of the fixture twice, and then adds the spring-back of a part that is already half welded. On thin sheet the second spot can land a millimetre or two out without anything obviously wrong at the machine - it shows up at assembly, where the holes no longer line up.
Both heads on the same frame, working opening between the upper and lower electrode arms
Two Heads On One Cast Frame
Both heads are mounted on a single cast frame: a heavy base with ribs under it, a column, and upper and lower arms reaching forward to form the working opening. Because the two heads sit on the same machined frame, the centre distance between them is a machined dimension rather than a fixture dimension - it does not move when a new operator loads the part, and it does not move over a shift.
The frame does a second job. A C-frame opens under electrode force: the arms deflect, part of the pressure that was set on the regulator never reaches the workpiece, and the weld is made at a lower force than the schedule says. Thick cast sections and a ribbed base are what keep that deflection down, which is why the frame is the heaviest part of the machine rather than the lightest.
|
|
|
|
Head column, cylinders and control cabinet from the side |
Both heads, one base - the spacing is built in |
Each Head Is Its Own Press
The two heads share a frame but not a cylinder. Each has its own air cylinder with its own regulator and its own adjusting handle on top, so the stroke and the electrode position of one head can be set without touching the other. When the two welds are not identical - different sheet thickness, a bracket on one side and a flat tab on the other - each head gets the pressure its own weld needs instead of a compromise between them.
Air is run to each head separately, in its own line, which also means a leak or a dropped pressure on one side shows up on that side only. The ram travels on the frame's guides, so the electrode comes down square to the workpiece rather than following the arc of a hinge.
|
|
|
|
Two heads from the operator side, cylinders and hose runs |
Head body, electrode arm and clamp block |
Top of a head: cylinder, adjusting handle and air fittings - each head is regulated on its own
The Electrodes, And The Green Board Between Them
The current path is copper end to end. A brass arm reaches forward from the head, clamps a vertical copper electrode holder in a split block, and the holder carries the electrode tip down into the working opening. The split block is the adjustment: loosen it, slide the holder up or down, and the tip is back where it was before it was dressed - without shimming and without touching the stroke.
The same arrangement sits underneath, mirrored, so the part is pressed between an upper and a lower electrode on one axis. Between the electrode arms and the steel frame there is a laminated insulating board - the green panel visible behind the arms. It is there so the welding current goes through the copper and the workpiece, not through the frame; if it went through the frame, the two heads would be electrically common and the current would take the shortest path instead of the one you set.
|
|
|
Upper and lower electrode on one axis |
|
|
|
|
|
Holder, clamp block and tip from the front |
Electrode between the brass work supports |
Arm, holder and the cooling hoses |
Six Circuits, And You Can See All Of Them
Cooling is not one line split six ways. The machine carries a bank of six variable-area flow meters on the frame, one per circuit, each with its own valve and its own float. Two heads, upper and lower electrodes, and the conductors behind them - and any one of them running short shows up as a float sitting low, at a glance, instead of as a hot electrode three hours later.
Air is laid out the same way: a filter-regulator-lubricator unit at the inlet, then a valve island with a solenoid per function and a red manual ball valve for each, so a head can be isolated for a tooling change without shutting the machine down. Water runs in yellow hose, air in blue - two services, two colours, no guessing when someone has to trace a line.
|
|
|
|
Six flow meters, one per cooling circuit |
Valve island with manual ball valves |
Filter, regulator and lubricator at the air inlet - one unit feeds both heads
Machine Configuration
|
Item |
Configuration |
|
Machine type |
Twin-head spot welding machine, fixed centre distance, single cast frame |
|
Heads |
Two C-frame heads, upper and lower electrode arms, one working opening each |
|
Press |
One air cylinder per head, independently regulated, adjusting handle on top |
|
Electrode force |
Set per head on its own regulator; balanced against the two welds |
|
Electrodes |
Brass arms, split clamp blocks, vertical copper holders, replaceable tips |
|
Insulation |
Laminated insulating board between electrode arms and frame |
|
Work support |
Brass support blocks with slots, set to the part |
|
Cooling |
Six circuits with individual variable-area flow meters and valves |
|
Air |
Filter-regulator-lubricator, valve island with manual ball valves per function |
|
Control |
Welding control cabinet with ammeter, digital display and front-panel settings |
|
Electrical |
Main electrical box on the base, cable and hose runs in protected bundles |
|
Frame |
Cast base with ribs, column and arms; free-standing on the floor |
|
Services |
Compressed air and cooling water; hoses colour-coded yellow for water, blue for air |
|
Options |
Tooling and work supports to the part drawing; head spacing set at build |
Transformer rating, welding current and electrode force are set from the part, the sheet thickness and the required nugget, and confirmed by sample welds before shipment - they are not a fixed catalogue figure.
Where Two Heads Pay For Themselves
• Long parts with a weld at each end - beams, rails, brackets, mounting ears
• Frames and panels with a stiffener or a tab on both sides
• Wire and sheet assemblies where two spots form one pattern
• Parts where the spot-to-spot distance is a bolt-up dimension, not a cosmetic one
• Thin sheet where a second set-up would let the part spring before the second weld
• Any job where the handling between two welds costs more than the welds do
Head spacing, electrode length and work supports are built to the part drawing. Where the two welds differ, the two heads are set up separately - that is the point of giving each its own cylinder.
From Part To Machine
01 Part drawing, weld positions and spot-to-spot distance review
02 Sample welds on your parts, nugget and pull test
03 Head spacing, electrode and work support proposal
04 Frame, head and tooling design
05 Cast frame, heads, arms and water circuit build
06 Welding control integration, pressure and flow set-up
07 Assembly, run-off on customer parts, weld section check
08 Crating and shipment as one unit
09 On-site installation, operator training, after-sales support
Talk to Pudian Technology
Guangdong Pudian Automation Technology Co., Ltd builds resistance and laser welding equipment in-house - transformers, controllers, electrodes, fixtures and complete machines - one team, one solution. Two welds on one part, and the distance between them matters? Send us the drawing and a sample, and we will build the heads to that distance.
|
Guangdong Pudian Automation Technology Co., Ltd WhatsApp / Tel: +13613793248 Email: jay@gd-pw.com Website: https://www.spotlaserwelding.com/ Address: 1-2F, Building 3, Qichen Industrial Park, No. 26 Luxi 1st Road, Liaobu Town, Dongguan City, Guangdong Province, China |