logo

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells

Basic Information
Place of Origin : Guangdong , China
Brand Name : PDKJ
Certification : CE ISO SGS
Model Number : Custom
Trade Information
Minimum Order Quantity : 1 unit
Price : 10000-30000 USD
Standard Packaging : Plywood Case
Delivery Time : 15-30 work days
Supply Ability : 100 set per month
Product Summary

Twin-gun platform spot welder DB-170W-S: vertical and horizontal gun, 170 kVA at 1000 Hz, copper table 800 x 1500 mm that doubles as the lower electrode, 750-850 mm electric lift.

Product Description
Contents

An Enclosure Needs Welds In Two Directions: Turn The Box Over For The Second One And The First Twelve Move

Application story  ·  Twin-gun platform spot welder DB-170W-S for enclosure shells - one vertical gun, one horizontal gun, an 800 x 1500 mm copper table that is also the lower electrode, electric height adjustment

A folded enclosure is welded on the inside, in two directions. The lid and the base meet the side walls in a lap that faces up - a vertical gun drops on it and welds. The side walls meet each other in a lap that faces sideways - the same gun cannot reach it. Weld the flat ones first, turn the box over for the rest, and the twelve spots you already made are now sitting in a part that has been lifted, turned and put down again. On 0.8 mm sheet that is enough to move a lap.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Twin-gun platform spot welder DB-170W-S: vertical gun on the centre column, horizontal gun on the right-hand swing arm, copper table, controls on the front of the table base

The Part: A Folded Shell, Welded On The Side Nobody Sees

The workpiece is the shell of a box - a control cabinet, an equipment enclosure, an electrical housing. Cold rolled or galvanised sheet, folded on a press brake, with a lap wherever two walls meet. The weld spots sit in those laps, on the inside. After welding the shell is cleaned and powder coated, so the only thing the customer sees is the outside face - and a spot that has pulled a dimple into it, or blown a hole through 0.8 mm sheet, cannot be filled and cannot be sold.

Two things follow. First, the electrode force has to be enough to fuse the lap and not enough to mark the outside. Second, every weld has to be reachable without taking the shell off the table, because the shell is the fixture - it is too large and too varied to clamp, and lifting it is what moves the laps that were already welded.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Enclosure shells, folded and punched, stacked for welding

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

A folded side panel - laps, stiffening beads and holes, ready for the table

The Table Is The Lower Electrode

There is no lower arm on this machine. The table is a solid copper plate, 800 x 1500 mm, and it is the return path: the current goes down the gun, through the lap, into the copper, and back to the transformer through the busbars bolted to the underside. That is why the shell does not need a fixture, a jig or a clamp - put it anywhere on the table, and wherever the gun comes down there is copper underneath it.

A copper table is also a surface that gets dressed rather than replaced. The face is skimmed and cleaned to keep it flat and conductive, and its condition is part of the process: a dirty patch under a weld is a high resistance joint. On the machines in these photographs the dressing marks are visible across the whole plate - that is a table still in use, not a worn one.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Copper table in use: gun on the left, horizontal gun swung in from the right, workpieces lying on the plate with the dressing marks of regular maintenance

Two Guns, Two Directions, One Set-Up

The vertical gun (390 mm) is carried on a slide on the centre column above the table and comes down under air pressure - that is the lid, the base and anything that faces up. The horizontal gun (300 mm) hangs on the right-hand swing arm, and it is moved by hand: the arm rotates on its joint, a balance cylinder takes the weight, and the operator brings the electrode in from the side onto the wall laps.

That is the whole argument for two guns rather than one. The second direction is welded without turning the shell over, so the laps that were welded first are still sitting flat on the copper where they were made - and the operator does not spend the shift lifting a box that weighs more than the weld does.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Vertical gun on the centre column, arm and hand gun swung out

From the operator side: table, controls, both guns in reach

The Table Goes Up And Down, The Shell Does Not

Table height is adjustable electrically between 750 and 850 mm, on the front of the base where the operator stands. It is a small feature that decides whether the machine is comfortable: a deep cabinet puts the weld line low, a shallow one puts it high, and the same operator works on both. Setting the table to the work, rather than the operator to the table, is what keeps the gun square to the lap at the end of a shift.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Machine at the bench, controls at the front of the table base: gun selection, start and stop within reach of both hands

170 kVA At 1000 Hz, And Why The Frequency Matters On Thin Sheet

The power source is a 1000 Hz inverter: 170 kVA rated capacity, up to 22 000 A short-circuit current, 20 % duty cycle, 2000 N electrode force. On thin sheet the frequency is not a specification to boast about, it is the reason the weld is repeatable. A conventional AC machine puts current in in half-cycles, and on 0.8 mm sheet a half-cycle too many is a hole while a half-cycle too few is a cold lap. A 1000 Hz inverter delivers DC with no zero crossing, so the heat goes in as a controlled block of time rather than as a piece of a mains wave, and the same setting produces the same nugget on the first shell and the five-hundredth.

Capacity is 3.0 + 3.0 mm on low-carbon steel and 2.0 + 2.0 mm on aluminium - comfortably above the 0.8 to 1.5 mm shells this machine is normally set up for, which is where the headroom for a heavier gauge or a doubled lap comes from.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Several units side by side on the floor - this is a series machine

Same row from the other end, arms and guns out

Key Specifications  -  DB-170W-S

Parameters

DB-170W-S

Rated capacity

170 kVA

Input power supply

3-phase 380 V

Rated frequency

1000 Hz

Welding gun type

Vertical welding gun / horizontal welding gun

Welding gun length

390 mm / 300 mm

Maximum short-circuit current

22 000 A

Duty cycle

20 %

Electrode pressure

2000 N

Welding capacity - low-carbon steel

3.0 + 3.0 mm

Welding capacity - aluminium plate

2.0 + 2.0 mm

Air pressure

0.6 MPa

Table size

800 x 1500 mm (customisable as required)

Table height

750 - 850 mm, electric height adjustment

Net weight / gross weight

800 kg / 963 kg

Where It Welds

•   Control cabinets, equipment enclosures and electrical housings - shells welded from the inside

•   Folded sheet 0.8 - 1.5 mm, where a dimple on the outside face is a reject

•   Boxes and panels with laps facing both up and sideways, welded without turning the work over

•   Small batches and one-offs: the copper table takes any size that fits 800 x 1500 mm

•   Galvanised and cold-rolled sheet, with the coating left intact around the nugget

•   Any job where a fixture would cost more than the parts it holds

Gun length, table size and table height are the three variables we set from the work: a deeper cabinet wants a longer vertical gun, a wider shell wants a bigger table. Both are quoted per job.

From Sample To Machine

01   Shell drawing, sheet thickness and lap positions review

02   Sample welds on your shells - nugget, outside face and pull test

03   Gun type, gun length, table size and height proposal

04   Machine build - column, arms, guns, copper table and lift

05   Inverter power source and control integration

06   Assembly and run-off on customer shells in our workshop

07   Crating and shipment

08   On-site installation, commissioning and operator training

09   After-sales support and spares

Built In Series, Shipped Assembled

This is a series machine, not a one-off: the units in these photographs were built side by side on the shop floor, wrapped, crated and loaded as complete machines. What arrives is levelled, connected to air and power, and welding - the setup that was proved on your sample is the setup that ships with it.

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Twin-Gun Platform Spot Welding Machine DB-170W-S for Enclosure Shells 

Wrapped and crated on the pallet before loading

Crated unit loaded for shipment

Talk to Pudian Technology

Guangdong Pudian Automation Technology Co., Ltd builds resistance and laser welding equipment in-house - transformers, controllers, electrodes, fixtures and complete machines - one team, one solution. Welding enclosure shells in two directions, without turning the box? Send us the shell drawing and a sample, and we will weld it on a copper table and show you both faces.

Guangdong Pudian Automation Technology Co., Ltd

WhatsApp / Tel: +13613793248    Email: jay@gd-pw.com

Website: https://www.spotlaserwelding.com/

Address: 1-2F, Building 3, Qichen Industrial Park, No. 26 Luxi 1st Road, Liaobu Town, Dongguan City, Guangdong Province, China


Send Us An Inquiry
We will reply to you within 24 hours.
Inquiry Details
Contact Information